News

1. The laser power supply will produce high voltage, so the equipment chassis, laser power, computer power must be well grounded, poor grounding may cause equipment failure, or even shorten the life of the laser tube, while high-voltage discharge will damage the motion control system, Serious cause personal injury, it should regularly check the ground thread with or without rust or loose, timely cleaning and fastening. 2. The size of the laser current determines the laser energy, will greatly affect the processing speed and quality, excessive current can be a corresponding increase in speed but will shorten the life of the laser, too small current and difficult to guarantee the cutting speed and Quality, so set the appropriate operating current parameters, to ensure a certain working speed in the case, can be a corresponding extension of the life of the laser. 3. Please avoid working with thunder and lightning. Excessive humidity caused by laser high voltage discharge, endangering personal safety, will lead to damage to the laser power supply, so the machine should be kept clean and dry. 4. The best cooling water temperature of the laser is 25-30 ℃, the water temperature is too high. The laser output energy will drop rapidly. When it rises above 50 ℃, it will cause the laser cavity to burst. When the water temperature is too low, Ice, will also lead to luminal rupture, so the operator should always pay attention to observe the cooling water temperature. 5. To maintain the equipment, at least 5 minutes after the power cut off. The movement part of the linear guide is contaminated or rust, will directly affect the processing effect, maintenance method for the cotton dipped into a little more clear oil, gently wipe the rails on both sides and surface dirt, wipe the machine when driving X, Y , Before and after the gradual cleaning. (More expertise on laser cutting machine Please pay attention to our website: www.vifalaser.com)

In some small and medium enterprises, the production of laser cutting machine, how to create a variety of new, unique and comprehensive capabilities to provide customers with a variety of laser cutting machine which is hard to do, then the state of existing resources how to operate the laser cutting machine can cut the effect is more accurate, and better yet, Guangdong VIFA laser Technology Co. with years of production and manufacturing experience to share with you laser cutting machine good results, and I hope to be useful. 1. Water protection should always check the cleaning, the cooling water is not often red water protection or water protection float switch float switch is not reset, you can not use the method to solve the pressing short. Cooling water quality is better, faucets aluminum oxide is too severe, a period of time necessary to regularly wash pumps and pipes, water protection in the dirt, or cause or cold laser tube burst head off. 2. The laser cutting machine laser tube mounting fulcrum must be reasonable and should be the fulcrum of the entire length of the laser tube 1/4, or cause deterioration in spot mode laser tube, flare into some work for some time at several points, resulting in decreased laser power Unable to meet the requirements, resulting in constantly changing tube. 3. The focusing lens and mirror checks on the frame work for a fever, the lens surface discoloration rust; Tuomo cracking belong to the object to be replaced, especially a lot of customers with a large air pump and air compressor, so that the focus the lens quickly stagnant water, so the time required for cleaning and inspection the quality of the lens (laser light outlet pipe) optical system. 4. Suction device should be on cleaning up, the fan duct clean. Otherwise a lot of dust and smoke did not break out, severe pollution fast lenses and laser tube, so that all mechanical and electronic components easily oxidized causing a bad contact. 5. The cooling system to the ground, often washing water tanks and water, cooling water tank thermostat temperature control point to be fair, or cause the laser tube easily damaged and condensation power down, off the cold water head pipe, shortened life expectancy, and sometimes does not work cause constantly changing tube. 6. Laser cutting machine working environment can not be too bad, if the ambient temperature is above 30 degrees, 18 degrees lower than the next, too much dust, air pollution severe, so severe damage to the machine, the failure rate rising; in a wet environment the electrical accessories easily the topic. So this remind customers to improve the working environment and the machine often for maintenance. 7. Laser tube operating current to be fair, can not work long-term in light intensity 90-100; to be fair application of lasers and laser energy conservation; optical system for a clean and accurate, otherwise cause premature aging and cracking of the laser tube, the laser work time should be adjusted in intensity by 50-60%, depending on the material and then to adjust the pace of work so that the laser tube is the best working condition. 8. The electric power grid to match. Power distribution departments and the contact point of the whole equipment to be good (fan, water-cooled machine, laser machine, laser power, the computer to an independent power supply).

Guangdong VIFA Laser Technology Co., Ltd. is a high-technology laser surgery as a guide, set design, development, manufacturing as one of the laser equipment and accessories professional production companies. Sophisticated equipment company, factory in strict accordance with ISO9001: 2000 quality system independent production. Equipment manufacturing speed and quality ranks with the industry-leading position. The company is located in Dongguan, Guangdong Province, covering 30,000 square meters. Founded in 1998, pre-order for each laser equipment manufacturers to provide high-quality laser machine parts for the main business projects, having taken advantage of a strong independent laser machine parts into the laser machine manufacturing industries. At present products have been sold to more than 70 countries and regions. Especially since 2013, the company based on customer demand at home and abroad, expanding the processing capacity of laser equipment, high-tech laser absorption of scientific research personnel, research and development to produce 17 kinds of new laser equipment, basic to effectively solve a variety of non-metallic materials difficult processing problems. Achieve a number of independent intellectual property rights owned laser cutting and engraving technology. The company ranks among the leading Chinese manufacturer of laser equipment ranks. VIFA Laser Main products: CO2 laser cutting machine, CO2 laser engraving machine, CO2 laser cutting machine camera, linear guide laser machines, automatic lifting rotary engraving laser machine, laser machine screw, automatic feeding laser cutting machine, automatic large format laser cutting, laser die cutter headed for machines, laser marking machine, CO2 laser marking machine, fiber laser marking machine, laser cutting machine burning flowers fabric, PU leather laser cutting machine, acrylic plexiglass laser engraving cutting machine, laser engraving rubber sheet and other comprehensive wealth of laser equipment. Support various types of customized non-standard laser equipment (function, color, size, shape and so can be customized). VIFA laser equipment widely used: leather leather, apparel fabrics, wood products, stone, glass, furniture making, model making, advertising, gifts, plastic, rubber, printing and engraving, packaging paper, decoration, metal materials , electronics, electrical, instrumentation, hardware, auto parts and other fields. And the era of convergence, in early 2015 the company launched the network marketing - "factory outlets, cut channels, sharing client." Give customers the best price to buy the most suitable machine. Growing together with customers, to provide the community with excellent products and services. VIFA electromechanical: outstanding laser equipment and accessories supplier!

Guangdong ViFa Laser Technology Co., Ltd. in September sent a technician to visit India customers this year, customers and give customers free training courses use the machine, check the machine for customers to resolve doubts, let customers more confidence to use the machine! Technicians and customer photo, We are very pleased to cooperate with friends in India. The customers through our laser cutting machine after the cutting products on display,and expressed satisfied with the cutting results. Customers together to learn to use the machine. Customer shooting cutting effect. Welcome new machines with local customs.